| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122 |
- /*
- * Configuration file for the SAMA5D2 Xplained Board.
- *
- * Copyright (C) 2015 Atmel Corporation
- * Wenyou Yang <wenyou.yang@atmel.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
- #ifndef __CONFIG_H
- #define __CONFIG_H
- /* No NOR flash, this definition should put before common header */
- #define CONFIG_SYS_NO_FLASH
- #include "at91-sama5_common.h"
- #define CONFIG_BOARD_EARLY_INIT_F
- #define CONFIG_MISC_INIT_R
- /* SDRAM */
- #define CONFIG_NR_DRAM_BANKS 1
- #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
- #define CONFIG_SYS_SDRAM_SIZE 0x20000000
- #ifdef CONFIG_SPL_BUILD
- #define CONFIG_SYS_INIT_SP_ADDR 0x210000
- #else
- #define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
- #endif
- #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
- /* SerialFlash */
- #ifdef CONFIG_CMD_SF
- #define CONFIG_SF_DEFAULT_BUS 0
- #define CONFIG_SF_DEFAULT_CS 0
- #define CONFIG_SF_DEFAULT_SPEED 30000000
- #endif
- /* NAND flash */
- #undef CONFIG_CMD_NAND
- /* MMC */
- #ifdef CONFIG_CMD_MMC
- #define CONFIG_GENERIC_MMC
- #endif
- /* USB device */
- #define CONFIG_USB_ETHER
- #define CONFIG_USB_ETH_RNDIS
- #define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D2 XPlained"
- #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
- #define CONFIG_DOS_PARTITION
- #endif
- /* I2C */
- #define AT24MAC_ADDR 0x5c
- #define AT24MAC_REG 0x9a
- /* Ethernet Hardware */
- #define CONFIG_MACB
- #define CONFIG_RMII
- #define CONFIG_NET_RETRY_COUNT 20
- #define CONFIG_MACB_SEARCH_PHY
- /* LCD */
- #ifdef CONFIG_LCD
- #define LCD_BPP LCD_COLOR16
- #define LCD_OUTPUT_BPP 24
- #define CONFIG_LCD_LOGO
- #define CONFIG_LCD_INFO
- #define CONFIG_LCD_INFO_BELOW_LOGO
- #define CONFIG_SYS_WHITE_ON_BLACK
- #define CONFIG_ATMEL_HLCD
- #define CONFIG_ATMEL_LCD_RGB565
- #endif
- #ifdef CONFIG_SYS_USE_MMC
- /* bootstrap + u-boot + env in sd card */
- #undef FAT_ENV_DEVICE_AND_PART
- #undef CONFIG_BOOTCOMMAND
- #define FAT_ENV_DEVICE_AND_PART "1"
- #define CONFIG_BOOTCOMMAND "fatload mmc 1:1 0x21000000 at91-sama5d2_xplained.dtb; " \
- "fatload mmc 1:1 0x22000000 zImage; " \
- "bootz 0x22000000 - 0x21000000"
- #undef CONFIG_BOOTARGS
- #define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk root=/dev/mmcblk1p2 rw rootwait"
- #endif
- /* SPL */
- #define CONFIG_SPL_FRAMEWORK
- #define CONFIG_SPL_TEXT_BASE 0x200000
- #define CONFIG_SPL_MAX_SIZE 0x10000
- #define CONFIG_SPL_BSS_START_ADDR 0x20000000
- #define CONFIG_SPL_BSS_MAX_SIZE 0x80000
- #define CONFIG_SYS_SPL_MALLOC_START 0x20080000
- #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
- #define CONFIG_SPL_BOARD_INIT
- #define CONFIG_SYS_MONITOR_LEN (512 << 10)
- #ifdef CONFIG_SYS_USE_MMC
- #define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
- #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
- #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
- #elif CONFIG_SYS_USE_SERIALFLASH
- #define CONFIG_SPL_SPI_LOAD
- #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
- #endif
- #endif
|
