Test/EVSE/GPL/cmake-3.11.0/Modules/CMakeExpandImportedTargets.cmake

# Distributed under the OSI-approved BSD 3-Clause License.  See accompanying
# file Copyright.txt or https://cmake.org/licensing for details.

#.rst:
# CMakeExpandImportedTargets
# --------------------------
#
# Deprecated.  Do not use.
#
# This module was once needed to expand imported targets to the underlying
# libraries they reference on disk for use with the :command:`try_compile`
# and :command:`try_run` commands.  These commands now support imported
# libraries in their ``LINK_LIBRARIES`` options (since CMake 2.8.11
# for :command:`try_compile` and since CMake 3.2 for :command:`try_run`).
#
# This module does not support the policy :policy:`CMP0022` ``NEW``
# behavior or use of the :prop_tgt:`INTERFACE_LINK_LIBRARIES` property
# because :manual:`generator expressions <cmake-generator-expressions(7)>`
# cannot be evaluated during configuration.
#
# ::
#
#  CMAKE_EXPAND_IMPORTED_TARGETS(<var> LIBRARIES lib1 lib2...libN
#                                [CONFIGURATION <config>])
#
# CMAKE_EXPAND_IMPORTED_TARGETS() takes a list of libraries and replaces
# all imported targets contained in this list with their actual file
# paths of the referenced libraries on disk, including the libraries
# from their link interfaces.  If a CONFIGURATION is given, it uses the
# respective configuration of the imported targets if it exists.  If no
# CONFIGURATION is given, it uses the first configuration from
# ${CMAKE_CONFIGURATION_TYPES} if set, otherwise ${CMAKE_BUILD_TYPE}.
#
# ::
#
#     cmake_expand_imported_targets(expandedLibs
#       LIBRARIES ${CMAKE_REQUIRED_LIBRARIES}
#       CONFIGURATION "${CMAKE_TRY_COMPILE_CONFIGURATION}" )

function(CMAKE_EXPAND_IMPORTED_TARGETS _RESULT )

   set(options )
   set(oneValueArgs CONFIGURATION )
   set(multiValueArgs LIBRARIES )

   cmake_parse_arguments(CEIT "${options}" "${oneValueArgs}" "${multiValueArgs}"  ${ARGN})

   if(CEIT_UNPARSED_ARGUMENTS)
      message(FATAL_ERROR "Unknown keywords given to CMAKE_EXPAND_IMPORTED_TARGETS(): \"${CEIT_UNPARSED_ARGUMENTS}\"")
   endif()

   if(NOT CEIT_CONFIGURATION)
      # Would be better to test GENERATOR_IS_MULTI_CONFIG global property,
      # but the documented behavior specifically says we check
      # CMAKE_CONFIGURATION_TYPES and fall back to CMAKE_BUILD_TYPE if no
      # config types are defined.
      if(CMAKE_CONFIGURATION_TYPES)
         list(GET CMAKE_CONFIGURATION_TYPES 0 CEIT_CONFIGURATION)
      else()
         set(CEIT_CONFIGURATION ${CMAKE_BUILD_TYPE})
      endif()
   endif()

   # handle imported library targets

   set(_CCSR_REQ_LIBS ${CEIT_LIBRARIES})

   set(_CHECK_FOR_IMPORTED_TARGETS TRUE)
   set(_CCSR_LOOP_COUNTER 0)
   while(_CHECK_FOR_IMPORTED_TARGETS)
      math(EXPR _CCSR_LOOP_COUNTER "${_CCSR_LOOP_COUNTER} + 1 ")
      set(_CCSR_NEW_REQ_LIBS )
      set(_CHECK_FOR_IMPORTED_TARGETS FALSE)
      foreach(_CURRENT_LIB ${_CCSR_REQ_LIBS})
         if(TARGET "${_CURRENT_LIB}")
           get_target_property(_importedConfigs "${_CURRENT_LIB}" IMPORTED_CONFIGURATIONS)
         else()
           set(_importedConfigs "")
         endif()
         if (_importedConfigs)
#            message(STATUS "Detected imported target ${_CURRENT_LIB}")
            # Ok, so this is an imported target.
            # First we get the imported configurations.
            # Then we get the location of the actual library on disk of the first configuration.
            # then we'll get its link interface libraries property,
            # iterate through it and replace all imported targets we find there
            # with there actual location.

            # guard against infinite loop: abort after 100 iterations ( 100 is arbitrary chosen)
            if ("${_CCSR_LOOP_COUNTER}" LESS 100)
               set(_CHECK_FOR_IMPORTED_TARGETS TRUE)
#                else ()
#                   message(STATUS "********* aborting loop, counter : ${_CCSR_LOOP_COUNTER}")
            endif ()

            # if one of the imported configurations equals ${CMAKE_TRY_COMPILE_CONFIGURATION},
            # use it, otherwise simply use the first one:
            list(FIND _importedConfigs "${CEIT_CONFIGURATION}" _configIndexToUse)
            if("${_configIndexToUse}" EQUAL -1)
              set(_configIndexToUse 0)
            endif()
            list(GET _importedConfigs ${_configIndexToUse} _importedConfigToUse)

            get_target_property(_importedLocation "${_CURRENT_LIB}" IMPORTED_LOCATION_${_importedConfigToUse})
            get_target_property(_linkInterfaceLibs "${_CURRENT_LIB}" IMPORTED_LINK_INTERFACE_LIBRARIES_${_importedConfigToUse} )

            list(APPEND _CCSR_NEW_REQ_LIBS  "${_importedLocation}")
#            message(STATUS "Appending lib ${_CURRENT_LIB} as ${_importedLocation}")
            if(_linkInterfaceLibs)
               foreach(_currentLinkInterfaceLib ${_linkInterfaceLibs})
#                  message(STATUS "Appending link interface lib ${_currentLinkInterfaceLib}")
                  if(_currentLinkInterfaceLib)
                     list(APPEND _CCSR_NEW_REQ_LIBS "${_currentLinkInterfaceLib}" )
                  endif()
               endforeach()
            endif()
         else()
            # "Normal" libraries are just used as they are.
            list(APPEND _CCSR_NEW_REQ_LIBS "${_CURRENT_LIB}" )
#            message(STATUS "Appending lib directly: ${_CURRENT_LIB}")
         endif()
      endforeach()

      set(_CCSR_REQ_LIBS ${_CCSR_NEW_REQ_LIBS} )
   endwhile()

   # Finally we iterate once more over all libraries. This loop only removes
   # all remaining imported target names (there shouldn't be any left anyway).
   set(_CCSR_NEW_REQ_LIBS )
   foreach(_CURRENT_LIB ${_CCSR_REQ_LIBS})
      if(TARGET "${_CURRENT_LIB}")
        get_target_property(_importedConfigs "${_CURRENT_LIB}" IMPORTED_CONFIGURATIONS)
      else()
        set(_importedConfigs "")
      endif()
      if (NOT _importedConfigs)
         list(APPEND _CCSR_NEW_REQ_LIBS "${_CURRENT_LIB}" )
#         message(STATUS "final: appending ${_CURRENT_LIB}")
      else ()
#             message(STATUS "final: skipping ${_CURRENT_LIB}")
      endif ()
   endforeach()
#   message(STATUS "setting -${_RESULT}- to -${_CCSR_NEW_REQ_LIBS}-")
   set(${_RESULT} "${_CCSR_NEW_REQ_LIBS}" PARENT_SCOPE)

endfunction()